A dead-end grip is a type of pole line hardware that connects to the eye thimbles on pole lines and communication lines.
They have a particular design that allows transmission on antennas, transmission lines, communication lines, and other guy structures.

The material that manufacturers use in making the dead-end grips are the same as the material of the strand.
The design is intended for single use, but for retention purposes, it is used twice within a 90-day window of installation.
The grip on the dead-end grip holds the conductors perfectly and prevents distortion on the conductors.

Why You Need a Dead-End Grip?

Dead-end grips are the best form of connections that are in use currently replacing the NLL, Ut, and NX tension clamps.
They are used on transmission lines and pole lines to hold the devices together and transmit power on power lines.

Be careful not to confuse it with dead-end cable grips which are common on OPGW/OPPC/ADSS lines of communication.
It is also known as the performed dead end grip and is in everyday use on AAC, AAAC, and ACSR steel wires and copper conductors.
It has very high grip strength, is easy to install, and is resistant to corrosion fitting the current demand on pole line hardware.

Features of Dead-End Grips

They have simple structures thus making them easy to install.
They also have a very high grip strength of up to 95% for the breaking load.
This explains why the breaking load is also very high.
It is resistant to corrosion mainly because the materials are the same as the materials of the conductor.
This mechanism makes it difficult for electrochemical corrosion to occur.
Apart from that it also passes through the process of hot-dip galvanization making it resistant to corrosion.

Types of Dead-End Grips

There are three main types of dead-end grips as explained below.
Dead end grips are of many types having different color marks because of the wide variety in diameter on the conductors.

· Guy Wire Dead End Grips

They are mainly in use for guying poles in constructing communication and power lines.
They work with guy strands of 1-inch diameter or less.
It has off-set tips to make installation very simple.
It is durable and reusable more than once after the first installation.
Besides, it also has color codes on both ends which help in its identification.
It has cable loops available for all strand sizes.

· Preformed Dead End

They have a particular design for use on Antenna, transmission, communication and other guyed structures.
This is among the most massive guy dead ends for use in large-scale installations.
It is also reusable, and the manufacturers make it using the same material as that of the conductors.

· Preformed Grips

The preforms of the guy wire apply widely on the dead-end poles and are reusable.
The material in use is the same as the material of the conductors.
It has a very high tensile strength and is resistant to corrosion.

Technical Specification of Dead-End Grips

Now, before buying a dead end grip, you should consider these technical specifications：

· Dimension

The dimensions on the dead-end grip are length and diameter.
Also, the length of the dead-end grip depends on the specifications of the customer and the kind of job it will perform.
The diameter is uniform and can also vary depending on the demands of the customer.

· Material Type

The main material manufacturers use in making dead-end grips are aluminum wires and galvanized steel wires.
Apart from that, aluminum clad steel can also be used to make the dead-end grips.
In most cases, the material of the conductor is the same as the material on the dead-end grip.
The materials mentioned above are also susceptible to corrosion and pass through the process of hot-dip galvanization.

· Finish – hot-dip galvanization

This is the primary process where the dead-end grips pass through to make them corrosion resistant.
It provides the dead-end grip with an extra coat that will keep corrosion away making it stronger and durable.

· Thickness

The thickness of the dead-end grip is dependent on the specifications of the customer.
Again, the diameter determines the thickness and the greater the diameter, the thicker the dead-end grip.
The thicker the dead-end grip, the higher the tensile strength.

· Design

The type of dead-end grip varies according to the plan.
Normally, the most common kind of dead-end grip has one hole at the end.
After bending it, it will have two holes at the end where the conductor will pass through.

· Tensile strength

Dead-end grips are supposed to have very high tensile strengths because of the kind of tension it has.
The tensile strength also varies depending on the type of material and the thickness of the material.
The stronger the material, the higher the tensile strength and the thicker the article, the more significant the tensile strength.

Dead End Grip Manufacturing Process

The primary raw material in the manufacture of dead-end grips is aluminum wires or steel wires.
The other material involved is cutting and measuring instruments.
Measure the steel wire and cut it to the right specifications.
After that, you will join the steel wires together and twist them so that they can fuse into one another.
Twist the whole system of steel wires to the end of the piece that you cut.
Make sure that it is twisted well to form a single piece with spaces in between for the conductor.
After that bend the new piece directly at the center forming a U shape.
In most cases, you will use galvanized to prevent it from corrosion.
If not, you will pass it through the process of hot-dip galvanization to make it resistant to corrosion.

Step-by-step Dead-End Grip Installation Process

The process of installing a dead-end grip is very simple and does not require the assistance of an expert. It is installed by hand, no need tool.
You will, however, require the assistance of an extra pair of hands to hold the device as you wrap it.
Put on gloves to protect your hands and also increase your grip on the dead-end grip.
Gather all the material you need to the working site among them being the dead-end grip.
Pass the dead-end grip through the eye thimble in case it is the connection in use.
Make sure that the connection goes all the way to the area with the bend.
After that, you will install the conductor along the strands of the dead-end grip.
Ensure it fits well into the strands on one side of the dead-end grip.
Fit it to the end of the dead-end grip.
The next step involves covering the strand using the other side of the dead-end grip.
With the help of an assistant holding the area with the bend, carefully wrap the straps.
Overlap the two sides of the dead-end grip slowly covering the conductor to the end.
At this point, the installation of the dead-end grip is complete, and you should proceed to the next step.